Iptv set-top box should be how to set it? I believe everyone is no stranger to iptv set-top boxes, in fact, it has telecommunications and Unicom two major communications vendors. Today, Xiao Bian did not say much about nonsense. Let's take a look at this iptv set-top box tutorial. 
Telecom iptv settings
1. Firstly, ensure that the video cable and power cable of the set-top box are correctly connected. Insert the wireless network card into the rear USB port of the IPTV STB or the USB interface on the side.
2. Turn on the set-top box and TV power supply and switch the TV to AV mode. (The mode to switch to is connected to your TV. After the IPTV set-top box starts up, the TV will show the Telecom IPTV image. Press the “Settings†button on the remote control to enter the configuration. The password (telephone password: 10000), select the right "OK" button to enter the configuration menu.After entering the password 10000, press the right arrow key of the remote control, then press OK.
3, enter the configuration menu, select "Network Settings", select "Wireless Connection", click "Next."
4. If the telecom installer has debugged a successful wired connection, do not modify the wireless PPPOE settings. Go to "Wireless Connection", select PPPOE, click "Next". (If the network cable access mode can be viewed normally, click here directly: wireless network settings)
5, enter the wireless PPPoE settings interface, enter the IPTV account number, password (general telecommunications home installation are set up, do not change)
6, return to the previous page, select the "wireless network settings" button to enter the following page, click "search", set-top box will search for wireless network signals, select "ChinaNet-IPTV (this name and the smart cat behind the wireless name is the same)", Authentication method select "WPA2PSK", the encryption method is AES, and the wireless key is: (Note: The wireless key can be seen behind the wireless cat, and the input method in the lower left corner of the remote controller can switch numbers and letters)
Note: The encryption method of the wireless network authentication method of the IPTV set-top box must be the same as that of the wireless cat. Otherwise, the connection may not be successful.
7. After the setting is completed, press “OK†to save and press “Cancel†button to return. Choose Save to exit. (Save password: 10000) At this point, all configurations of the EC1308 STB are completed. IPTV wireless dial-up connection, normal test program viewing.
Note: The IPTV wireless receiver must be used in conjunction with wireless smart cats (in the case of wireless smart cats without cracking the wireless routing function), customers without wireless smart cats need to purchase or configure wireless routers themselves, and the working mode of the router is: dynamic IP Mode (this mode of operation may cause the mobile phone and IPAD cannot WIFI Internet access), otherwise it may not be able to watch IPTV normally.
Unicom iptv settings
1. The set-top box is connected to the second network port of the ONU through the network cable.
2. The red, white and yellow lines of the set-top box are respectively connected to the sockets of the corresponding colors of the set-top box and the television. After confirming the connection is correct, the set-top box is powered on.
3. After the above physical connection is normal, the LAN2 light of the front panel of the Optical Cat ONU is always on, and the second light (LINK or connection) of the set top box is also constantly on.
4. Different set-top box terminals will have slightly different settings. At present, Tianjin Unicom's free set-top box has the following two brand models: ZTE and Huawei.
ZTE set-top box is set as follows:
1. Click on "Settings" on the remote control, password 6321.
2. Select basic settings and click OK.
3, select the wired connection, click Next.
4. Select DHCP. The username and password are empty. There is no authentication. Click Next.
5, enter the business account: Broadband 11 code 0220; password, click OK, restart the set-top box can be.
Huawei STBs are illustrated as follows:
1. After the STB is connected to the normal power-on, the boot screen is found as follows
2, the first time landing, automatically jump to the following screen, enter the account password, account: broadband 11-bit code 0220, password 12345678, click OK to restart the set-top box.
Telecom iptv settings
1. Firstly, ensure that the video cable and power cable of the set-top box are correctly connected. Insert the wireless network card into the rear USB port of the IPTV STB or the USB interface on the side.
2. Turn on the set-top box and TV power supply and switch the TV to AV mode. (The mode to switch to is connected to your TV. After the IPTV set-top box starts up, the TV will show the Telecom IPTV image. Press the “Settings†button on the remote control to enter the configuration. The password (telephone password: 10000), select the right "OK" button to enter the configuration menu.After entering the password 10000, press the right arrow key of the remote control, then press OK.
3, enter the configuration menu, select "Network Settings", select "Wireless Connection", click "Next."
4. If the telecom installer has debugged a successful wired connection, do not modify the wireless PPPOE settings. Go to "Wireless Connection", select PPPOE, click "Next". (If the network cable access mode can be viewed normally, click here directly: wireless network settings)
5, enter the wireless PPPoE settings interface, enter the IPTV account number, password (general telecommunications home installation are set up, do not change)
6, return to the previous page, select the "wireless network settings" button to enter the following page, click "search", set-top box will search for wireless network signals, select "ChinaNet-IPTV (this name and the smart cat behind the wireless name is the same)", Authentication method select "WPA2PSK", the encryption method is AES, and the wireless key is: (Note: The wireless key can be seen behind the wireless cat, and the input method in the lower left corner of the remote controller can switch numbers and letters)
Note: The encryption method of the wireless network authentication method of the IPTV set-top box must be the same as that of the wireless cat. Otherwise, the connection may not be successful.
7. After the setting is completed, press “OK†to save and press “Cancel†button to return. Choose Save to exit. (Save password: 10000) At this point, all configurations of the EC1308 STB are completed. IPTV wireless dial-up connection, normal test program viewing.
Note: The IPTV wireless receiver must be used in conjunction with wireless smart cats (in the case of wireless smart cats without cracking the wireless routing function), customers without wireless smart cats need to purchase or configure wireless routers themselves, and the working mode of the router is: dynamic IP Mode (this mode of operation may cause the mobile phone and IPAD cannot WIFI Internet access), otherwise it may not be able to watch IPTV normally.
Unicom iptv settings
1. The set-top box is connected to the second network port of the ONU through the network cable.
2. The red, white and yellow lines of the set-top box are respectively connected to the sockets of the corresponding colors of the set-top box and the television. After confirming the connection is correct, the set-top box is powered on.
3. After the above physical connection is normal, the LAN2 light of the front panel of the Optical Cat ONU is always on, and the second light (LINK or connection) of the set top box is also constantly on.
4. Different set-top box terminals will have slightly different settings. At present, Tianjin Unicom's free set-top box has the following two brand models: ZTE and Huawei.
ZTE set-top box is set as follows:
1. Click on "Settings" on the remote control, password 6321.
2. Select basic settings and click OK.
3, select the wired connection, click Next.
4. Select DHCP. The username and password are empty. There is no authentication. Click Next.
5, enter the business account: Broadband 11 code 0220; password, click OK, restart the set-top box can be.
Huawei STBs are illustrated as follows:
1. After the STB is connected to the normal power-on, the boot screen is found as follows
2, the first time landing, automatically jump to the following screen, enter the account password, account: broadband 11-bit code 0220, password 12345678, click OK to restart the set-top box.
Square Hole Breadboard,400 Tie Point Breadboard,Makeronics Breadboard,Small Solderless Breadboard
Cixi Zhongyi Electronics Factory , https://www.zypcbboards.com